Upgraded Ar 15 Lower Parts Kit

Upgraded Ar 15 Lower Parts Kit

Here we are offer best quality for Upgraded Ar 15 Lower Parts Kit and guarantee cheaper than other online shopping store. Look inside store for get more discount,If you want to see more details Can be ordered at the online store that we recommend

  • IN STOCK
  • UP TO 70% OFF
  • FAST SHIPPING

*** Please check more details at the merchant website.

Recommend Products Hot price.

Reiff & Nestor Company
Reiff & Nestor Company "perfect Cut" Premium Tap - 6-40 Bottom Two-Flute Tap


Not magic, just perfect! When we first tried these taps (recommended by customer Dan Baldwin), we thought they were extra hard, coated or treated somehow . . . they're that much better than any tap we've ever used before. But, the U.S. company that's been making them since 1912 says the secret is plain old care and quality control. The ground threads are held to incredibly tight tolerances for roundness, thread spacing, etc. Result is, all the teeth cut equally so the whole tapping process goes faster, the taps last longer, breakage is cut way down and the threads are the finest you'll ever see. Try them; you'll tap more holes per tap than you thought possible! Premi Mfg: Reiff & Nestor Company SPECS: H-2, High Speed tool steel.Check price and Read more Detail At Reiff & Nestor Company

Brownells Steel One Caliber Sets - Steel One Caliber Set Fits .17 Cf Muzzle (.165
Brownells Steel One Caliber Sets - Steel One Caliber Set Fits .17 Cf Muzzle (.165")


Set includes: one, 90 facing cutter to square a muzzle after shortening, or repair damage; one, 45 chamfering cutter to break the edges of the rifling for a clean bullet exit or chamfer a revolver cylinder mouth for quick reloads; plus one handle that fits either cutter and one steel bore pilot. Interchangeable pilot keeps cutter properly aligned. Purchase extra pilots to use one cutter for many different calibers. Pilots for other calibers available separately. Mfg: Brownells SPECS: Facing Cutter X"X Hardened steel. 3¼" (8.2cm) long (except .165" cutter, 2-3/8" (6cm) long). 1" (2.5cm) or .750" (19mm) diameter as required. Chamfer Cutter X"X Hardened steel. 3¼" (8.25cm) long (except .165" cutter, 2-3/8" (6cm) long). ½" (12.7mm) or 5/8" (15.8mCheck price and Read more Detail At Brownells

Brownells Metal Checkering Files - 75 Lpi (#4)
Brownells Metal Checkering Files - 75 Lpi (#4)


The only way to get true, accurate line spacing when checkering backstraps, triggerguards, grip frames, ribs and hammer spurs; anywhere an improved gripping surface is needed. Finer cuts give a nice matting effect to reduce glare and light distortion. Procedure is very similar to wood checkering. Layout your master lines (or use a guide like our .45 Checkering Guide), then establish the pattern by moving the file a few teeth each time using the previous lines as the guide. Once the pattern is fully laid out, bring to final depth with a 60° needle file. Mfg: Brownells SPECS: 8" (20.3cm) length x ½" (12.7mm) wide. Cutting area: 6" (15.2cm) x ½" (12.7mm).Check price and Read more Detail At Brownells

Grsc Car-15 Car Ambidextrous Sling Adapter - Car Ambidextrous Sling Adapter
Grsc Car-15 Car Ambidextrous Sling Adapter - Car Ambidextrous Sling Adapter


Steel, sling adapter replaces the standard issue, receiver plate to provide a rock solid attachment point for fast handling, tactical slings on CAR-15 rifles. Ambidextrous slots accept 1¼" wide webbing, rings accommodate carry straps with snap fasteners. Allows the sling to be switched from right or left side of receiver in seconds. Keeps sling tangle-free and provides the proper balance and stability for hands-free carry. Mfg: Grsc SPECS: Steel, Parkerized finish. 2-9/16" (6.5cm) long, 2-1/16" (5.2cm) high, 3/32" (2.4mm) thick. Fits CAR-15 rifles.Check price and Read more Detail At Grsc

Copyright © 2020 Increase Sale Now RN53. All Rights Reserved