Tikka Tac A1 308

Tikka Tac A1 308

Here we are offer best quality for Tikka Tac A1 308 and guarantee cheaper than other online shopping store. Look inside store for get more discount,If you want to see more details Can be ordered at the online store that we recommend

  • IN STOCK
  • UP TO 70% OFF
  • FAST SHIPPING

*** Please check more details at the merchant website.

Recommend Products Hot price.

Redding Body Dies - Body Die 6.5 Prc
Redding Body Dies - Body Die 6.5 Prc


Body Dies are designed to full length resize the case body, bump the shoulder position for proper chambering, but not size the neck at all. They are made without internal parts and are intended for resizing cases which have become increasingly difficult to chamber after repeated firing. After using a body die, the case should be run through the neck die to achieve proper neck tension. Sold separately or as part of a set. Mfg: ReddingCheck price and Read more Detail At Redding

Burris Ar-Pepr Permanent Mounts - 1
Burris Ar-Pepr Permanent Mounts - 1" Ar-Pepr Mount


One-piece cantilever mount with integral rings positions the optic almost 2" farther forward to provide extra clearance needed for a night vision device (NVD), add-on magnifier, or long eye relief scope. The "Proper Eye Position Ready" mount also features built-in, two-slot rails on the tops of the rings for convenient mounting of reflex sights or other accessories. Each top ring strap is secured with six Torx screws to prevent recoil-induced slippage. Side locking bar with two, steel hex nuts and cross-bolts hold tight on any Picatinny receiver rail. Smooth contours and radiused edges give a streamlined appearance, reduce weight, and prevent snagging. Mfg: Burris SPECS: Aluminum, hardcoat anodized, matte black. 5.3" (13.5cm) long, 1.6" (4.1cm) wide, 2.4" (6.1cm) overall height. Height from top of rail to bottom of ring: 1" (2.5cm). 8.7 oz. (247g) weight. Fits scopes with 1" tube. Mounts to MIL-STD 1913 Picatinny rails.Check price and Read more Detail At Burris

Sinclair 7/8-14 Benchrest Press - C-Frame 7/8
Sinclair 7/8-14 Benchrest Press - C-Frame 7/8"-14 Benchrest Reloading Press


Our Sinclair Custom Press is designed for bump-sizing benchrest cartridge shoulders in the field and in the reloading room. The features on this press are the result of input from dozens of benchrest shooters who use small, portable presses like these.Details like the 10-degree press tilt, the covered linkage, and the primer exit point make this press stand out from all others. Features:- Machined and contoured from a solid billet of aluminum.- A soft radius has been applied to all edges to eliminate sharp corners.- Primers exit through the bottom of the ram, keeping primer debris away from the linkages.- Throat opening of 2.5 inch will accept up to 308 case lengths for Mfg: Sinclair InternationalCheck price and Read more Detail At Sinclair International

Brownells 3 1/2% Nickel Steel Welding Rod - .094
Brownells 3 1/2% Nickel Steel Welding Rod - .094" 8 Oz.


Developed for use in our space program to give the best possible welds, 3½% Nickel Steel Welding Rod is almost totally free of impurities and flows beautifully to produce an extremely smooth, non-porous weld with Oxy-Acetylene or TIG. Over the years many gunsmiths have asked for this rod to weld bolt handles and other items that will be polished after welding. Thanks to Jim Thompson, Maverick Gun Works of Topeka, Kansas, we've located a supplier of 3½% Nickel Steel Welding Rod. Says Jim, "I finally located some 3½% Nickel Steel Rod and the first bolt I welded was perfect. The rod is expensive but worth its weight in gold when you are welding bolt hand Mfg: Brownells SPECS: Each piece is approximately .094" (2.4mm) or .045" (1.14mm) diameter, - 12" (30.5cm) long. Sold in 4 oz. (113 g), 8 oz. (227 g) and 1 lb. (454 g) paks.Check price and Read more Detail At Brownells

Copyright © 2020 Increase Sale Now RN53. All Rights Reserved