Springfield Armory Xdm Backstrap Roll Pin

Springfield Armory Xdm Backstrap Roll Pin

Here we are offer best quality for Springfield Armory Xdm Backstrap Roll Pin and guarantee cheaper than other online shopping store. Look inside store for get more discount,If you want to see more details Can be ordered at the online store that we recommend

  • IN STOCK
  • UP TO 70% OFF
  • FAST SHIPPING

*** Please check more details at the merchant website.

Recommend Products Hot price.

Rcbs 30 Remington Neck Die Set
Rcbs 30 Remington Neck Die Set


This 30 Remington Two-Die Neck Die Set is for bottleneck cases to be fired in bolt-action rifles only-specifically, cases fired out of a specific rifle and neck-sized to go back into the same rifle. The set consists of a Neck Sizer Die with an Expander-Decapping Unit, and a Seater Die with Bullet Seater Plug. The Neck Sizer Die resizes the neck only (it doesn't touch the shoulder or body) and de-primes. The included Seater Die has a built-in roll crimper to secure the bullet at the same time it's seated. Mfg: RcbsCheck price and Read more Detail At Rcbs

Beretta 486 20 Gauge Extractor Left Hand
Beretta 486 20 Gauge Extractor Left Hand


BERETTA 486 20 GAUGE EXTRACTOR LEFT HAND Mfg: Beretta UsaCheck price and Read more Detail At Beretta Usa

Brownells Shotgun Barrel Polishing Flex Hone - Flex Hone 10 Gauge Med. Bore
Brownells Shotgun Barrel Polishing Flex Hone - Flex Hone 10 Gauge Med. Bore


Hundreds of abrasive "balls" mounted on a flexible shaft - the fastest, easiest way we've come across to clean and polish older barrels or put a mirror polish in new ones. For used barrels, the Medium-Coarse hone, followed by the Fine, removes rough and tight spots and brings the bore to a bright finish that you can see and feel . . . just run a patch through it before and after; the difference is amazing! We found too, that we could feel tight spots during honing and spend extra time on them until they were evened out. On new barrels, the Fine hone by itself will bring the factory finish up to a beautiful, mirror-bright finish that's a real customer pleaser. Easy to use Mfg: Brownells SPECS: Flex Hone for Barrels; 10, 12, 16, 20 ga., .410 bore. 33" (83.8cm) long in Med.-Coarse grit (red tip) or Fine grit (light blue tip). Flex Hone for Chambers; 10, 12, 16, 20 ga., .410 bore 12" (6.5cm) long, fine grit (light blue only). Set includes Med.-Coarse & FineCheck price and Read more Detail At Brownells

Cylinder & Slide 1911 Trigger Pull Kits - Tactical Ii 4lb Trigger Pull Kit, Ss
Cylinder & Slide 1911 Trigger Pull Kits - Tactical Ii 4lb Trigger Pull Kit, Ss


Each kit is tested on a Series 70-style frame to make certain it will produce the specified pull weight with little or no fitting. Parts are wire EDM cut from bar stock, honed and polished, then heat treated for years of service life. All profiles and through-holes are mechanically correct to function without hand fitting. Sear nose has correct relief angle, sear spring is narrowed to reduce pull weight. Exposed hammer edges on Ultra-Light, Super?Match and Tactical II are chamfered to minimize slide drag and clothing wear. Each kit contains a hammer, sear, disconnector, sear spring and hammer spring. ULTRA LIGHT KIT - 3.5 lb. pull weight. Ultra light, skeletonized, hammer; relieved to pre Mfg: Cylinder & Slide SPECS: Ultra Light Kit: Special die steel, in-the-white. Hammer: Rc 50-53. .39 oz. (11.1 g) weight. Sear: .07 oz. (1.9 g) weight. Ultra Light Speed II: Tool steel, in-the-white. Hammer & Sear: Rc 50-55. .7 oz. (20g) total weight. Sear: .07 oz. (1.9 g) weight. Tactical II Kit: Special tool steCheck price and Read more Detail At Cylinder & Slide

Copyright © 2020 Increase Sale Now RN53. All Rights Reserved