Savage Firing Pin

Savage Firing Pin

Here we are offer best quality for Savage Firing Pin and guarantee cheaper than other online shopping store. Look inside store for get more discount,If you want to see more details Can be ordered at the online store that we recommend

  • IN STOCK
  • UP TO 70% OFF
  • FAST SHIPPING

*** Please check more details at the merchant website.

Recommend Products Hot price.

Brownells Brass One Caliber Set - Brass One Caliber Set Fits .35 Muzzle
Brownells Brass One Caliber Set - Brass One Caliber Set Fits .35 Muzzle


Set includes: one, 90 facing cutter to square a muzzle after shortening, or repair damage; one, 45 chamfering cutter to break the edges of the rifling for a clean bullet exit or chamfer a revolver cylinder mouth for quick reloads; plus one handle that fits either cutter and one brass bore pilot. Interchangeable pilot keeps cutter properly aligned. Purchase extra pilots to use one cutter for many different calibers. Pilots for other calibers available separately. Mfg: Brownells SPECS: Facing Cutter X"X Hardened steel. 3¼" (8.2cm) long (except .165" cutter, 2-3/8" (6cm) long). 1" (2.5cm) or .750" (19mm) diameter as required. Chamfer Cutter X"X Hardened steel. 3¼" (8.25cm) long (except .165" cutter, 2-3/8" (6cm) long). ½" (12.7mm) or 5/8" (15.8mm) dCheck price and Read more Detail At Brownells

Brownells Oil Hardening Drill Rod Round - 1/2
Brownells Oil Hardening Drill Rod Round - 1/2" Gauge, .5000 Dec. Equiv.


O-1 OIL HARDENING DRILL ROD ROUND Carbon - .95% Manganese - 1.20% Silicon - .25% For ¼" round and larger, we carry oil hardening drill rod rather than water hardening. The O-1 in this size range is characterized by good machineability, smooth finish as well as superior dimensional stability and excellent hardening characteristics. We recommend it for use in dies, tools, parts, and punches. Excellent for general use in the shop. HARDENING: Heat slowly to 1475° F. - 1525° F. If a controlled furnace is not available, use 1500° Tempilaq. Hold at this temperature for a few seconds then quench in a light quenching oil. TEMPERI Mfg: Brownells SPECS: Rods are 18" in length.Check price and Read more Detail At Brownells

Hornady Flash Hole Deburring Tool
Hornady Flash Hole Deburring Tool


The Hornady Flash Hole Deburring Tool is designed to be inserted into the case mouth and uses the web of the case as a safety stop. The tool is then given a couple of turns and it produces a small chamfer on the inside edge of the flash hole. This operation removes any burrs that might be present surrounding the flash hole insuring proper, uniform ignition. Flash hole deburring is a one-time operation and best used on brand new cases. For .224 caliber through 45 caliber cartridge cases. Stock# for handle is 749-012-872. Mfg: HornadyCheck price and Read more Detail At Hornady

Brownells Stainless Steel Roll Pin Kit - 1/8
Brownells Stainless Steel Roll Pin Kit - 1/8" Dia., 1/2" (12.7mm) Length Roll Pins, Qty 24


With the increasing use of roll pins in guns, we've been looking for a good assortment of them in stainless steel to offer. Finally found it - with 850 pins in 8 diameters and various lengths (see below). Should take care of most gun needs!Great for other shop jobs too. Make jigs, fixtures, or use to replace taper pins, dowels, groove pins, set screws, etc. Will not slip or vibrate out. Easy to use, as require no threading or taping. Can be cut to any length. Use the Roll Pin Punches for positive, safe removal. Mfg: Brownells SPECS: Kit (and Refill Paks) includes: 192 total 1/16" (1.6mm) diameter pins; 180 total 5/64" (2mm) diameter pins; 144 total 3/32" (2.4mm) diameter pins; 96 total 1/8" (3.2mm) diameter pins; 144 total 5/32" (2mm) diameter pins; 36 total 3/16" (4.8mm)diameter pins; 36 total 7/32" (5.6mm) diaCheck price and Read more Detail At Brownells

Copyright © 2020 Increase Sale Now RN53. All Rights Reserved