Casey Long Kel Tec

Casey Long Kel Tec

Here we are offer best quality for Casey Long Kel Tec and guarantee cheaper than other online shopping store. Look inside store for get more discount,If you want to see more details Can be ordered at the online store that we recommend

  • IN STOCK
  • UP TO 70% OFF
  • FAST SHIPPING

*** Please check more details at the merchant website.

Recommend Products Hot price.

Cylinder & Slide 1911 Trigger Pull Kits - Ultra Light Trigger Pull Kit
Cylinder & Slide 1911 Trigger Pull Kits - Ultra Light Trigger Pull Kit


Each kit is tested on a Series 70-style frame to make certain it will produce the specified pull weight with little or no fitting. Parts are wire EDM cut from bar stock, honed and polished, then heat treated for years of service life. All profiles and through-holes are mechanically correct to function without hand fitting. Sear nose has correct relief angle, sear spring is narrowed to reduce pull weight. Exposed hammer edges on Ultra-Light, Super?Match and Tactical II are chamfered to minimize slide drag and clothing wear. Each kit contains a hammer, sear, disconnector, sear spring and hammer spring. ULTRA LIGHT KIT - 3.5 lb. pull weight. Ultra light, skeletonized, hammer; relieved to pre Mfg: Cylinder & Slide SPECS: Ultra Light Kit: Special die steel, in-the-white. Hammer: Rc 50-53. .39 oz. (11.1 g) weight. Sear: .07 oz. (1.9 g) weight. Ultra Light Speed II: Tool steel, in-the-white. Hammer & Sear: Rc 50-55. .7 oz. (20g) total weight. Sear: .07 oz. (1.9 g) weight. Tactical II Kit: Special tool steCheck price and Read more Detail At Cylinder & Slide

Sherwin-Williams Tri-Flow - Tri-Flow, 12 Oz. Aerosol
Sherwin-Williams Tri-Flow - Tri-Flow, 12 Oz. Aerosol


Lubricant reinforced with PTFE (same stuff used on non-stick frying pans) displaces moisture, dirt, grit, rust, salt, and other contaminants from friction surfaces and forces them to flow away. A surface cleanses itself (no more buildup) of harmful wear particles. Further, galling is practically impossible with Tri-Flow - a "curse" with many so-called "dry" lubricants. On shop gears, "ways", spindles, and moving parts, wear life is extended. On gun parts it's like installing ball-bearings. On frozen parts or where rust is deep, penetration and release can be within minutes or seconds. Temperature limits: 65° F. to +475° F Mfg: Sherwin-Williams SPECS: Available 4 oz. (118.2mL) or 12 oz. (354.7mL) aerosol container. Ozone safe aerosol.Check price and Read more Detail At Sherwin-Williams

Clymer Pull Through Chamber Reamers - .308 P/T Reamer Only
Clymer Pull Through Chamber Reamers - .308 P/T Reamer Only


The same special reamers military armorers have long used to cut minimum length chambers on match rifles, giving their shooters the accuracy advantage. The gun's own bolt applies pressure to the reamer while reamer is turned from the muzzle end. When the bolt "drops", the chamber is cut. Improved design cuts the shoulder, neck and throat to prevent neck crimping of the ammo. Use as a finish reamer ONLY. Cut chamber with conventional finish reamer first. Superb quality reamers made to SAAMI specifications. Mfg: Clymer SPECS: .308 & .30-06 Reamer Sets include: Pull Through (P/T) Reamer, Thrust Bushing and Extension Shaft. Shaft - 24" (60cm) long, ¼" (6.3mm) diameter, round shank. Use #184-054-653 Throater/.22 T-Handle to drive shaft. Reamers work on bolt action or semi-auto rifles.Check price and Read more Detail At Clymer

Friedr. Dick Gmbh Screw Head Files - Screw Head File #11, .043
Friedr. Dick Gmbh Screw Head Files - Screw Head File #11, .043"


High-quality, steel files designed for one purpose only X"X to cut perfectly square screw slots every time. #7, #9, and #11 files cover the most common slot sizes. Smooth-sided to cut only on the edge. Will not widen the slot as it deepens, or damage the screw head. Cleans up marred slots on hard to replace screws or cuts slots in new screws. Use with Needle File Handles. These files are very thin for precise cutting. Sorry, cannot guarantee against bending or breakage. Sold individually or as a set. Mfg: Friedr. Dick Gmbh SPECS: 5¾" (14.6cm) overall length. Shank is 1½" (3.8cm) long. Thickness: #7 - .027" (.69mm), #9 - .035" (.89mm), #11 - .043" (1.1mm). Set includes one each, #7, #9, #11 files.Check price and Read more Detail At Friedr. Dick Gmbh

Copyright © 2020 Increase Sale Now RN53. All Rights Reserved